Compact Equipment

SEP 2018

Compact Equipment is a magazine dedicated to equipment owners and operators of small, nimble, tool-carrying construction, landscape and ag equipment — such as skid steers, mini excavators, compact tractors, generators compressors and beyond.

Issue link: http://digital.compactequip.com/i/1023491

Contents of this Issue

Navigation

Page 50 of 55

www.compactequip.com 51 • See if all driving and warning lights are functional. Not all engine or machine manufacturers will have low- level warnings, so it is a good practice to perform a visual check often. If everything checks out okay, it is time to start greasing. All pivot points will need to be greased either prior to starting or ending the shift, depending on operator pref- erence. Greasing also includes the articulation point, which is commonly forgotten. It is important to clean the grease fitting prior to greasing the joint. Failing to do so will push the accumulated dirt on the fitting into the pin boss. The dirt will contaminate the grease and act like sandpaper in- side the pin boss between the bushing and pin, resulting in premature wear. Final areas to address are all related to the operator's safety. Before climbing into the cab, the operator should clean the mirrors and windows, especially if they used pressurized air or water to clean debris. Once in the operator's seat, the final check is to ensure the brakes are functional and the backup alarm is working. Weekly Maintenance Weekly or roughly every 100 hours, the machine should be thoroughly greased at the pivot points, bushing and bearing. Other than additional greasing, maintenance tasks for this interval require a deeper dive than daily tasks. This includes: • Check the lug nuts on each tire and tighten to the appro- priate torque. • See if the electrical connections, cables and plugs have any issues. • Clean and securely attach the battery contacts. • Make sure there are no blown fuses or loose connections in the fuse panel. • If dirty, clean the radiator and oil cooler from the inside out with compressed air or high-pressure water. However, tread carefully to avoid damaging anything in the process. • If necessary, clean and replace the engine air filter. This is especially true for operators working in dusty environ- ments like demolition applications. Do not use high-pres- sure compressed air to clean the air filter or hit it against anything as this can result in damage. Hours-Based Service It is important to log hours while utilizing a compact wheel loader. This is because there are some additional tasks to take care of when the machine reaches 250 and 500 hours. 250 Hours: Depending on the manufacturer, the engine oil and fuel filters should be changed every 250 hours. Most engine manufacturers require an initial engine oil change after the break-in period. Following this, oil change intervals are usually 250 to 500 hours. The oil level in the front and rear axles, power divider and all four planetary drives should be checked. Initial service for the planetary assemblies after the first 250 hours is also recommended. 500 Hours: The oil in the front and rear axles, power divid- er and all four planetary drives should be changed within the initial 500 hours. Following the initial period, these will only need to be replaced every 1,500 hours. Lastly, axle breathers should be replaced, in addition to checking battery posts for corrosion and cleaning if necessary. Your Annual Checkup: The next big service intervals are 1,500 and 3,000 hours. At this point, the oil in the axles and hy- draulic system is nearing the end of its service life and should be replaced. Thorough checks of the machine should also be made to ensure there are no loose or worn parts. 1,500 Hours: As mentioned before, the oil in the axles, power divider and planetary drives needs to be replaced. Additionally, change the hydraulic oil and service the brake system. 3,000 Hours: Every 3,000 hours, replace the hydraulic oil, air filters and breathers. This is a good time to ensure all bolts and screws are tightened to the proper torque speci- fications. It is important to look at hydraulic hoses for fa- tigue, cracking or leaks, and replace them if any of these issues are discovered. Start Your Engines Depending on the manufacturer, a diesel engine will likely need maintenance at additional specific hour inter- vals. Some of this will simply consist of fluid changes, valve train adjustments and fuel and exhaust system checks. With a turbo-equipped engine, one operational technique is vital to the health of a compact wheel loader: the warmup and cool down. Allow the engine time to warm up prior to put- ting the machine under a load, and let it cool down before completely shutting it off. Because the engine is small, it is a common misconception that cold starts and hot shutdowns won't harm it. Eliminate the Threat of Machine Failure Most failures that occur could have been avoided with proper maintenance. Here are a few things to pay special at- tention to. Greasing the machine is vital to longevity with the large amount of articulating and pivoting components. The articulation joint is constantly moving and under a lot of stress. To eliminate premature wear of the pins and bush- ings, the articulated joint needs plenty of grease. Along with this area, the steering cylinders and loader pivot points need adequate grease daily. Other considerations include operator turnover. Different operators will arrive and use the wheel loader to load the truck themselves with a mindset that either the next person will grease the machine and check the oil or the machine has already been greased and checked over. In the end, the loader goes days without being properly greased or having any of the vital fluid levels checked. When it comes to main- tenance, the best place for information is still the service or operator's manual. Keith Kramlich is a national service and warranty manager at Takeuchi-US.

Articles in this issue

Archives of this issue

view archives of Compact Equipment - SEP 2018